IEC 60335-2-87-2002 家用和类似用途电器.安全.第2-87部分:牲畜用电昏迷设备的特殊要求

上一篇: IEC 60335-2-70-2002 家用和类似用途电器.安全.第2-70部分:挤奶机的特殊要求
下一篇: IEC 60335-2-86-2002 家用和类似用途电器.安全.第2-86部分:电动捕鱼机具的特殊要求

标准名称：	纤维片材加固修复结构用粘接树脂
英文名称：	Resin for strengthening and restoring structures with fiber laminate
中标分类：	建材 >> 建材产品 >> 粘结材料
ICS分类：	建筑材料和建筑物 >> 建筑材料 >> 粘合料、密封材料
发布部门：	中华人民共和国建设部
发布日期：	2004-12-02
实施日期：	2005-03-01
首发日期：	1900-01-01
作废日期：	1900-01-01
提出单位：	建设部标准定额研究所
归口单位：	建设部建筑制品与构配件产品标准化技术委员会
起草单位：	中冶集团建筑研究总院、国家工业建筑诊断与改造工程技术研究中心、广东泛达化工有限公司
起草人：	岳清瑞、杨勇新、陈小兵、张才鹏、张成英、彭勃、范世平等
出版社：	中国标准出版社
出版日期：	2004-12-23
页数：	16开， 页数：9， 字数：13千字
书号：	155066.2-16044

本标准规定了纤维片材加固修复结构用粘接树脂的术语及定义、分类、型号及标记、要求、试验方法、检验规则、标志与包装、运输与贮存。本标准适用于使用纤维片材对土木工程结构进行加固修复的粘接树脂。

没有内容

没有内容

没有内容

Product Code:SAE J1832
Title:Low Pressure Gasoline Fuel Injector
Issuing Committee:Gasoline Fuel Injection Standards Committee
Scope: This SAE Recommended Practice promotes uniformity in the evaluation and qualification tests conducted on fuel injectors used in gasoline engine applications. Its scope is limited to electronically actuated fuel injection devices used in automotive port or throttle body fuel injection systems where fuel supply pressure is below 1000 kPa. It is primarily restricted to bench tests. More specifically, this document is intended for use as a guide to the following:Standardize use of nomenclature specifically related to fuel injectors.Identify and define those parameters that are used to measure fuel injector characteristics or performance. The parameters included in this document are listed along with their recommended symbol where appropriate:Closing Time (CT)Inductance (L)Coil Resistance (R)Dynamic Flow (Qd)Dynamic Flow Calculated (Qdc)Dynamic Flow Rate (Q)Dynamic Flow Temperature Shift (Qtd)Dynamic Flow Vacuum Shift (Qvd)Dynamic Minimum Operating Voltage (DMOV)Dynamic Set Point (PWxx)Dynamic Set Point Flow (Qsp)External LeakageFlow-Offset (Y)Insulation Resistance (IR)Linear Flow Range (LFR)Linearity Deviation (LD)Maximum Overload VoltageOpening Time (OT)Operating Voltage RangePeriod (P)Pulse Width (PW)Pressure Drop Ratio (PDR)RepeatabilitySlope (m)Slope Approximated (ma)Spray PatternStability (S)Static Drop-Out Current (I/S-OFF)Static Flow Rate (Qs)Static Minimum Operating Voltage (SMOV)Static Pull-In Current (I/S-ON)Time-Offset (X)Working Flow Range (WFR)Establish test procedures and recommend test equipment and methods to measure and quantify these parameters.Establish test procedures, and recommend test equipment and methods to quantify simulated field reliability over the life of the component.Except where stated, test results are recorded for individual parts under recommended test conditions. Where population characteristics are reported, the sample size, selection method, and analysis technique must be explicitly stated.Any testing practices which are different than those recommended in this specification should be noted on the data collection sheet.
Rationale: This SAE Recommended Practice promotes uniformity in the evaluation and qualification tests conducted on fuel injectors used in gasoline engine applications. Its scope is limited to electronically actuated fuel injection devices used in automotive port or throttle body fuel injection systems where fuel supply pressure is below 1000 kPa. It is primarily restricted to bench tests. More specifically, this document is intended for use as a guide to the following:Standardize use of nomenclature specifically related to fuel injectors.Identify and define those parameters that are used to measure fuel injector characteristics or performance. The parameters included in this document are listed along with their recommended symbol where appropriate:Closing Time (CT)Inductance (L)Coil Resistance (R)Dynamic Flow (Qd)Dynamic Flow Calculated (Qdc)Dynamic Flow Rate (Q)Dynamic Flow Temperature Shift (Qtd)Dynamic Flow Vacuum Shift (Qvd)Dynamic Minimum Operating Voltage (DMOV)Dynamic Set Point (PWxx)Dynamic Set Point Flow (Qsp)External LeakageFlow-Offset (Y)Insulation Resistance (IR)Linear Flow Range (LFR)Linearity Deviation (LD)Maximum Overload VoltageOpening Time (OT)Operating Voltage RangePeriod (P)Pulse Width (PW)Pressure Drop Ratio (PDR)RepeatabilitySlope (m)Slope Approximated (ma)Spray PatternStability (S)Static Drop-Out Current (I/S-OFF)Static Flow Rate (Qs)Static Minimum Operating Voltage (SMOV)Static Pull-In Current (I/S-ON)Time-Offset (X)Working Flow Range (WFR)Establish test procedures and recommend test equipment and methods to measure and quantify these parameters.Establish test procedures, and recommend test equipment and methods to quantify simulated field reliability over the life of the component.Except where stated, test results are recorded for individual parts under recommended test conditions. Where population characteristics are reported, the sample size, selection method, and analysis technique must be explicitly stated.Any testing practices which are different than those recommended in this specification should be noted on the data collection sheet.